How to Remove the Coil From a Stihl Trimmer

Preliminary preparation

First, to wind the fishing line, you need to remove

reel (bobbin, spool) from the trimmer - certain actions will depend on the complexity of the configuration and the type of the product itself:

small electronic trimmers with a working arrangement of the motor and coil in the lower part usually have side buttons on both sides of the reel. By simultaneously pressing them, the upper part of the reel, together with the internal contents for winding the fishing line, is disconnected, while the lower part remains on the trimmer. It is better to disassemble the bobbin on a flat, smooth place so that the spring included in the structure does not jump out and get lost;
electronic and gasoline trimmers with a curved rod without the ability to install a knife usually have reels with a special wing: in similar designs, you should hold the spool in a stationary position with one hand, and with the other hand, turn the wing nut that locks the reel on the rod counterclockwise. After disconnecting the nut, the entire bobbin is removed.
electronic and gasoline trimmers with the ability to install a knife on a straight rod (for example, Stihl ) have a hole under the reel. To keep the rod stationary, a screwdriver or other suitable object is inserted into this hole, and with a slow rotation, such mutual placement is achieved when the screwdriver goes inside the hole and the reel is fixed. After which the coil body is rotated clockwise (with a left-hand thread) and removed from the trimmer .

For the second and third options, the coils, depending on the design, are disassembled using different methods. In reels with a lamb, the lamb is turned out, in reels with latches, the latches are pressed and one part of the reel is released from the other. If the halves of the spool are connected by thread, then it is enough to turn them by hand in the opposite direction until they are completely unscrewed.

Preliminary preparation

At first, to wind the fishing line you need to remove

reel (bobbin, spool) from
the trimmer - certain actions will depend on the complexity of the configuration and the type of the product itself:

small electric trimmers with a working arrangement of the motor and coil in the lower part usually have side buttons on both sides of the reel. By simultaneously pressing them, the upper part of the reel, along with the internal contents for winding the fishing line, is disconnected, while the lower part remains on the trimmer. It is better to disassemble the bobbin on a flat, smooth place so that the spring included in the design does not jump out and get lost;
electric and gasoline trimmers with a curved rod without the ability to install a knife usually have reels with a special wing: in similar designs, you should hold the spool in a stationary position with one hand, and with the other hand, turn the wing nut that locks the bobbin on the rod counterclockwise. How to thread the line into the trimmer? How to thread line into a trimmer reel. It’s clear how to load the line onto the trimmer. After disconnecting the nut, the entire reel is removed.
electric and gasoline trimmers with the ability to install a knife on a straight rod (for example, Stihl ) have a hole under the reel. To keep the rod stationary, a screwdriver or other suitable object is inserted into this hole and, with slow rotation, such mutual placement is achieved when the screwdriver fits inside the hole and the reel is fixed. After this, the coil body is rotated clockwise (with a left-hand thread) and removed from the trimmer.

READ How to Adjust the Carburetor on a Stihl Trimmer

For the second and third options, the coils, depending on the design, are disassembled in different ways. In bobbins with a wing, the wing is unscrewed; in bobbins with latches, the latches are pressed and one part of the bobbin is released from the other. How to thread a fishing line into a cheap fishing line. 2. On your site. If the halves of the spool are connected by a thread, then it is enough to turn them by hand in reverse directions until they are completely unscrewed.

What types of fishing lines are there?

The most common type of fishing line, which is suitable for almost all types of reels, is round cord. This is an ordinary fishing line , suitable for mowing succulent grass, but it will be much more difficult to mow dead wood, and even more so it will not cope with bushes.

As a rule, the diameter with which young grass can be mowed does not exceed 1.6 mm. The thicker the thread, the coarser the grass it can overcome.

There are fishing lines with sharp edges in the form of an asterisk or a square; this option is more suitable for mowing dry grass due to the existing sharp edges, but its disadvantage is greater wear and is inferior in strength to round cord.

There are fishing lines with improved aerodynamics with characteristic dents, scales and notches; such a product makes less noise, but it is used only on lawn mowers, since it is difficult for such thread to come out of the spool; it is most often used with disks into which segments are inserted. The disadvantage of this product is its fragility.

Most often in gasoline trimmers with an engine power of more than 1.5 hp. cords with a metal cable inside are used.

READ How to Thread Line into the Reel of a Champion Trimmer

This thread is ideal for mowing dry grass and small shrubs. The presence of a core has a positive effect on the wear resistance of this material.

The disadvantage of such a cord is its price, which is significantly higher than the above listed opponents.

Automatic winding of line onto reel

There is a type of reel in which an automatic mechanism produces winding without the help of others - the user only needs to thread the line correctly. How to thread line into the trimmer reel? annotation. How to remove the coil from the trimmer? How to wind the fishing line in order to thread the fishing line. The fishing line is passed through a hole on the inside of the body, its tendrils are threaded through the hole on the outer body without winding, the bobbin is assembled, and when the winding button is rotated, the fishing line inside is wound independently. In such a spool it is impossible to wind it incorrectly: the mechanism itself will determine the correct direction, because it can only spin in one direction.

trimmer factory refill

will inevitably require line replacement. Having a very rough idea of how to thread the line into the trimmer reel without the help of others, newbies are reluctant to take on this task. But with certain abilities, mastering this simple science does not present any difficulties, and a similar abstract presented below will greatly facilitate this process.

How to Remove a Pressed Coil From an Electric Trimmer

LED lighting fixture AQUARIUM is cheap and cheerful. Trimmer BOSCH ART twenty-three SL in operation. How to start a gasoline cutter. Gasoline trimmer. Start cool petrol cutters. Electronic trimmer SKIL seven hundred thirty-five AA. Trimmer Bosch ART twenty-six SL complete. Trimmer FORTE EMK-360, changing the mowing line. Barbecue for feeding from a gas cylinder yourself. How to wind fishing line onto a trimmer reel. Trimmer BOSCH ART twenty-six COMBITRIM. Cheap trimmer BOSCH ART twenty-three SL. How to wind fishing line onto a trimmer reel? Trimmer BOSCH ART twenty-three EASYTRIM. Bosch ART twenty-three SL. How to assemble and launch a trimmer (scuticoriza) part 3.5. BOOB NURSERY FROM CHINA.

With this trimmer you don't need to pick up the spool every time, it is very important to change the line in the existing spool to a new skein.

To change the ruler for the BOSCH ART twenty-three Easytrim trimmer, I suggest using these instructions that I provided below.

The bosch art twenty-three easytrim trimmer, according to the instructions, should have a 1.6 mm wide line, but this device will perfectly convey a 2.7 mm wide line. And sometimes I would like to note that a two-mm fishing line will make the mowing process easier.

Installing a reel of mowing line.

Secure the coil resistance sixteen so that it does not twist.

Return the coil cover fourteen counterclockwise and remove.

Remove the empty spool seventeen from the cover.

Pass the end of the new or tightened spool through the hole

15 and install the coil in cover 14.

Run about nine cm of mowing line from the reel.

Install the spool with cover 14 onto the support

Now you need to take five meters of new mowing line and fold it in half (to find the middle). In the middle part of the reel, of course, there is a recess (in some structures a hole) into which you need to hook our fishing line. There is also an arrow on the reel indicating the direction of winding. An important detail if the coil has two.

Many owners of garden scythes are struck by the issue of changing the mowing line in the trimmer head. At the same time, this turns into a whole problem that can make not only the tool, but also the mower additionally inoperable. To prevent such a situation, we will step by step analyze the process of changing the cord (mowing line) in the attachment.

1. Remove the attachment from the gearbox. To do this, you need to align the side hole or washer of the upper shape and the recess on the axle, insert a screwdriver and secure the shaft from spinning. Then it is possible to unscrew the nozzle. Keep in mind that the thread on the shaft has a left-hand cut, so you need to unscrew the element by turning it to the right.

2. The next step is to disassemble the device body. Typically the lid is secured through slotted holes using latches. To open it, you need to insert the valves into the body and press the edges of the lid. If the attachments have an automatic or automatic line feed mode, it means there is a spring inside when.

I want to dedicate this article to the painful topic of summer residents and gardeners throughout the post-Soviet space: How to fill out a line in a trimmer. Not all of the Russian automotive trimmer industry answers this question in its operating instructions. Therefore, it is also difficult for ordinary gardeners to understand how to do this correctly.

How to thread line into the reel of a Stihl trimmer

How to thread line into a trimmer

? annotation

Warranty production of the trimmer's factory refill will inevitably require replacement of the fishing line. Having a very rough idea of how to thread the line into the trimmer reel without the help of others, new ones are reluctant to take on this task. How to wind fishing line onto a trimmer reel, how to thread fishing line into a trimmer reel. Autocut for trimmer

stihl fs 55 threading fishing line into the trimmer reel part 2 winding the fishing line on. But with some opportunities, mastering this simple science does not present any difficulties, and the similar instructions presented below will greatly facilitate this process.

Reel with two working antennae

In this type of spool, you should find the number of grooves for winding line lying on the inside of the reel:

one groove - both tendrils are wound together along one groove;
two grooves - each tendril is wound along a personal groove.

For both cases, a fishing line 2-3 m long is taken. In single-groove reels, the fishing line is pulled into a through hole, its ends (tendrils) are folded together and aligned, after which they are wound in the opposite direction of rotation of the reel on the rod - the correct direction of winding is usually indicated on the inside by an arrow. If there are locking grooves, the ends of the fishing line are threaded into them or held with the fingers of your free hand, threaded into the through hole of the outer half of the reel, the spool is locked and attached to the trimmer rod.

READ How to Dilute Gasoline for a Stihl Trimmer

The difference between winding fishing line in two-groove reels is that first a piece of fishing line 2-5 m long is folded in half (to determine the middle fold), and the fold loop is inserted into a special groove between the grooves. Both antennae of the fishing line are wound each along their own groove; fixing the antennae and assembling the reel is similar to the option discussed above with one groove.

The first implementation of this procedure may seem long and quite labor-intensive, but with the passage of time and experience this problem will be solved much faster and easier.

The following will clearly show how to thread the line into the trimmer

and wind it correctly - this operation is not difficult at all and, with some patience, will certainly be crowned with success:

Replace the fishing line with a disk or knife

When finishing gardens, park areas and other places where you need to mow various types of plants, you often have to change the cutting tool in the trimmer. This is because the standard cord installed in the mower head can only work on grass. But when a bush or young tree sprout appears in the worker’s path, the fishing line cannot cope with this task and must be replaced with a more efficient cutting tool.

Manufacturers of trimmers have foreseen similar situations and supplemented their products with a mass of attachments in the form of knives with several “petals” or in the form of disks similar to circular saws.

If you replace the line with a knife with several “petals”, then this tool can mow both tall grass and plants with thick and dry stems. And by changing the line on the disc, the user gets the ability to use the mower to trim bushes or small trees.

Knives and wheels are installed according to the following algorithm.

The first step is to remove it by securing the shaft, cutting head (turn clockwise) or the shoe nut if the unit has not yet been used.
Position the saw or cutting blade so that it rests on the small projection (sleeve).

READ Stihl Fs 55 Trimmer Gear Lubricant

Place the mounting cap on the blade and screw the nut onto the shaft (counterclockwise).
Tighten the nut (counterclockwise) with a pipe wrench.

You can watch this video to better understand the tool changing process.

Is it possible to make a coil for a trimmer with your own hands?

Take a piece of plywood or PCB and draw a circle on it with a diameter of about 14 cm.
Cut out the disc using a jigsaw or hacksaw.
Drill a hole in the center of the disk that fits the diameter of the gearbox shaft. Do not forget to put a washer on it before installing the disk on the shaft.
You can screw small corners on the sides of the disk or make 1-2 holes on the reverse sides. They will serve to thread their fishing lines.
To secure the fishing line, you can screw several self-tapping screws into the plywood.

READ Stihl 170 AND 180 V What's the difference

This homemade mowing attachment is secured to the shaft with a nut. It is impossible to tighten or unscrew the nut without fixing the shaft. To change the cord, it will be enough to loosen the screws, insert a piece of fishing line of the required length and press it down again.

Also, a mowing attachment for attaching a fishing line to it can be made from an iron sheet. How to do this can be understood from what follows.

The method of attaching attachments may be different for different models. But in general terms the design is very identical. Here is a step-by-step summary:

Locate the hole in the gear cup (it is located either on top or on the side) and align it with the hole in the shaft hub.
Insert a hex wrench or an iron rod into the hole in the gearbox to prevent the shaft from turning.
Hold the key with one hand and unscrew the spool of fishing line with the other (usually you need to turn it clockwise).
Remove the coil.

Before removing the line spool on the trimmer, the tool must be unplugged. If you have a walk-behind mower, be sure to turn off the engine.

Scaffold winding algorithm

Depending on the trimmer model used, the type, thickness and length of the mowing line are selected. The diameter of the cord can be from 1.2 to 4 mm. It is not difficult to guess that the thicker you thread the cord, the tighter and thicker it can be cut.

There are 3 ways to find out what diameter line you can use on your mower.

Refer to the device manual for cord thickness information.
Look at the coil itself. It may be marked with information about the possible diameters of the mowing line.
Insert the line into the socket. If it fits easily, you can use a cord of that diameter.

The line is wound onto a reel located in the mowing head. Therefore, it needs to be opened first (this was discussed above). There are two ways to wind the cord.

First way

To correctly determine how many meters of fishing line are needed for a particular reel, it is necessary to wind it onto the reel so that the reel does not exceed the diameter of the boards. If the line extends beyond the edges of the spool, you cannot insert it into the cap. Once you have decided on the length of the material, you need to load it into the spool, so do the following.

You need to fold the fishing line in half, so that one end is 10-15 cm longer than the other.
Please note that the coil is divided into 2 parts by the central side, from which charging begins. Find the recess on it and insert the cord, bent in half, into it with a little force.
It is very important to determine in which direction the line is wound to the reel. If you look closely, you may find an arrow on the reel or a label with an arrow indicating which direction to wind. There are cases when there is no arrow on the reel. In this situation, you can look at the painted arrow on the mower head and wind the cord in the opposite direction.
Winding should be done carefully, wrap the spool with maximum thread tension.
Once the cord is finished, you must first secure the short end of the mowing line by inserting it into a slot of the appropriate diameter on the side of the reel.
The other end, the genuine one, is installed in a groove on the opposite side of the coil.
After securing the mowing line, cut off its ends, leaving an allowance of about 10 cm.
Next, you need to install the aged reel into the mowing head. To do this, insert and pull the threads into the outlet holes of the head, insert the reel into the body, and then, applying the necessary force, pull the line out of the mounting grooves and tighten it.
You can now put the cover on and secure it with the latches.

READ How to remove the crankshaft oil seal on a trimmer

Second way

Some reels provide a second way to secure the cord: instead of one folded in half, you can load 2 pieces of thread. . the fishing line is replaced in accordance with the following algorithm.

Before replacing or loading new filament into the spool, determine how many meters you will need as described above.
Bend one end of the cord into a hook.
Find the hole at the bottom of the spool to secure the line and insert the bent end of the thread into a loop.
It is necessary to wind the cord in accordance with the direction of the arrow to the desired level, not exceeding the diameter of the reel.
Do the same for the second coil socket.
Assembling the head is no different from the method that was envisaged when threading the reel, considered with a double piece of fishing line.

For Stihl brand motor braids there is a very simple and quick way to change the line without disassembling the mower, which you can see by watching this video.

The ends of the cord protruding from the holes in the housing can be trimmed to the required length when the part is installed in the trimmer. There are two ways to do this:

Turning on the trimmer (during rotation, the ends of the fishing line will be trimmed around the knife attached to the protective cover for this purpose);
Trimming the excess ends with scissors so that they do not touch the body.

The second method is used if you need to put on a large diameter cord and the cutter cannot shorten it.

If the thread is threaded onto the mowing head, but the protruding ends of the cord are not long enough, they must be lengthened before starting the machine. This applies to a manually adjustable head . However, there are times when using a semi-automatic mower when, due to the insufficient length of the protruding ends of the cord, they do not automatically extend. In this case, you must turn off the unit (it is absolutely necessary to remove the plug from the socket on the electrical device), manually press the button located at the bottom of the part, and pull out a little fishing line. After this procedure, the cord will be able to lengthen again due to centrifugal force if you set the spindle speed to maximum.

Battery trimmer options

Cordless scythes are easy to use; they actively help clear the area near the house of weed. Such devices contain batteries with a charge indicator. You can simply adjust the bar and handle.

Advantages of battery trimmers:

without noise, also without wires, you can care for lawns;
the best option for amateur use;
It is light in weight and has excellent balance.

The equipment comes in a series, and the following comes into it.

Barbell with height adjustment. It can be adjusted at any time. Perfectly suitable for those conditions when the unit is used by several people, and everyone can adapt it to suit themselves.
The handle is shaped like a circle and is easy to adjust. It has 6 positions.
The mowing unit is adjustable. This can be done in four positions.
The edge can be cut vertically. With all this, the angle can be changed up to 90 degrees.

The most famous versions of braids on batteries are listed below.

Recommendations related to repairs

Mechanical problems are caused by damage to the trimmer head. In most cases, this component is subject to wear and tear, and this element often comes into contact with the environment. There are several options for a breakdown that is mechanical in nature.

Sources:

https://svistun.info/agrogorod/kak-snyat-katushku-s-leskoy-s-trimmera-shtil.php https://moreremonta.info/strojka/kak-snjat-katushku-s-trimmera-shtil/