How to Remove the Clutch on a Shtil Chainsaw

Repair of any equipment must begin with the preparatory work stage, and the Stil 180 saw is no exception. At the preparatory stage, before disassembling the Shtil 180 chainsaw, it is necessary to remove the side cover, chain and tire from the chainsaw. Next, using a compressor and a brush, you need to clean the chainsaw from dirt, sawdust, oil stains and other things.

When cleaning the saw, special attention should be paid to the place where the chainsaw drive sprocket is located, since this is the most contaminated area.

In places where there is a large accumulation of oil, you can wash it with clean gasoline.

When to remove the clutch

Disassembly of the clutch for the purpose of removal is carried out in the following cases:

• when the spring bursts (the chain turns, the engine runs intermittently);
• the spring flew off;
• a piece of the drum has broken off (in this case, noise will be heard and the chainsaw chain will also spin);
• temporary wear (it’s time to remove and change the clutch due to the end of its life).

Modern chainsaws operate on two-stroke engines, which are connected by a gearbox to the saw chain. The chain moves along the bar, and according to the centrifugal principle, idling should remain motionless, that is, be safe for the person holding the chainsaw.

If the load placed on the tool exceeds the recommended load, the clutch will weaken or completely stop transmitting torque to the tire. This will cause the engine to stop. When such situations occur, the clutch wears out and therefore needs to be replaced over time. In the operating instructions for chainsaws, some manufacturers have information that the clutch is a consumable part, that is, it must be periodically replaced.

Video - how to remove the clutch on a chainsaw:

How to Remove the Clutch on a Shtil Chainsaw

how to remove the clutch of a Stihl chainsaw

How to remove a sprocket from a Husqvarna chainsaw. Repair of the Chinese chainsaw Stihl ms 660. replacement of the drive sprocket, partial disassembly SHOCK! When repairing the Stihl chainsaw with your own hands, you need to use the method of elimination, alternately inspect Disassembly and assembly of the Stihl MS 180. The Stihl MS 180 is a reliable and undemanding tool, but requires repair from time to time, as well as no matter what kind of equipment. At the preliminary step, before disassembling the Shtil 180 chainsaw, you need to remove the side cover from the chainsaw. In the Other Auto Topics section, to the question of how to remove the brake clutch from the crankshaft of the Stil chainsaw given by the creator Lyudmila Brova, the best answer is I do So, I take a rope and tie knots on it with a distance of approximately two centimeters, remove the locking ring, disconnect the air damper, remove the throttle, pull out the accelerator with the spring. New saws should be selected according to the characteristics indicated in the operating instructions for the Shtil 180 chainsaw. Construction, repairs with your own hands. How to remove the clutch on a chainsaw calm? And yet, repairing a chainsaw can take a lot of time. No instructions on repairing a chainsaw will change the usual logic of the chainsaw clutch How to remove the chainsaw clutch? The clutch drum is immediately the drive sprocket. How to remove the chainsaw clutch. Repair of chainsaw Shtil ms 180 frequent breakdown. How to remove magneto from chainsaw. A VERY NECESSARY THING A key for removing the clutch in a Chinese chainsaw. Bulkhead repair Stihl MS180. chainsaw is not the cheapest to repair and has some factory defects, but at the same time it is light, small-sized and resourceful. Comfortable at work. We remove the breaker by unscrewing two 19 nuts with a spark plug wrench. Where it is used: all STIHL chainsaws. 16. Clutch . remove it to replace the sprocket by removing only one retaining ring. Replacing the chain sprocket is very simple: it can be changed. Remove the clutch on the Chinese Shtil 180 chainsaw yourself. video, tips from Kosi Kosy.

The question of how to remove the clutch on a chainsaw arises as often as the urgency of replacing the part itself. Communities Do It Yourself Blog Repairing a STIHL 180 chainsaw photo report (Part 1). And make sure that there is a vacuum discharge from a small hole when the carb is removed. So did you repair it or not? Otherwise, when choosing a saw, they sang to me that a calm is better than a husqvarna Clutch . Chainsaws are equipped with a centrifugal clutch, which is activated automatically depending on the number. The latter prevents snow from entering the air purification system and is used only in winter; at above-zero temperatures it is removed. How to remove the clutch (clutch) from a chainsaw, part 2. 01:56.

Clutch repair for Stihl MS 250 chainsaw. 09:54. How to change the star on a Partner? 03:38. How to unscrew clutch . 01:08. Where to use: all STIHL chainsaws. 16. Clutch . remove it to replace the sprocket by removing only one retaining ring. Replacing the chain sprocket is very simple: it can be changed. Which oil to fill for the Stihl 180 chainsaw (stihl 180).16:53. After checking the oil supply to the tire, everything works fine, there is no leak in the hose, and when the tire is removed, oil flows out of the channel. Homelight carburetor malfunction. How to remove the clutch on a MS 180 calm? The chainsaw must be brought for diagnostics to the nearest authorized service center. Homelight carburetor malfunction. How to distinguish a copy of STIHL 180 from the ORIGINAL. I made this video for people who are planning to buy their first chainsaw. Be Disassembling the Shtil 180 chainsaw part 1. Do-it-yourself repair of the Shtil 180 chainsaw. chainsaw is designed for inexperienced users to operate. If you remove the muffler from the Shtil, you can visually assess the condition of the cylinder and piston group by looking into the hole from the muffler. I do this: I take a rope and tie knots on it with a distance of about two centimeters, then I turn out the candle and push the rope in there (this is to stop the crankshaft, otherwise it won’t be unscrewed) and everything can be unscrewed. Husqvarna chainsaws have one clutch spring and two weights, Shtil chainsaws have three clutch springs and three weights (cams, sectors). How to remove the clutch the clutch cup should be along the axis. Good afternoon, dear readers, I’m Andrey Noak in touch. In this article, I decided to briefly talk about how I repaired the Shtil 180 chainsaw with my own hands. In fact, this story is like a whole mini-adventure that happened to me on vacation. clutch is found on every modern tool. For the tool model being repaired, remove the clutch, remove the clutch and carefully inspect the drum and mechanism parts. This task is faced every time there is a need to remove the drive sprocket and (or) the clutch of the chainsaw. - on some models of saws (in particular on the Shtil-180) there may be a washer between the clutch and the drive sprocket cup. How to remove the clutch (clutch) from a chainsaw part 1. Duration: 3:10 Vitos 2,613 views. how to remove the clutch on a chainsaw. Duration: 3:05 FREZZA Service 1,581 views. The movement of the chain along the chainsaw bar is carried out by a drive sprocket connected to the engine gearbox. Wear on the spline on the sprocket indicates that it needs to be replaced as soon as possible. Return to contents. Algorithm for replacing the clutch drum. clutch covers the sprocket. For example, in a Stihl chainsaw, there may be a washer between the sprocket and the motor. You need to remember its position, remove it and repeat. The popularity of the Shtil 180 chainsaw is due to its reasonable price and excellent characteristics. In order to identify the problem, you need to remove the cover and a special screen from the carburetor, which is located behind the tool drum. How to remove the clutch from a Shtil 180 chainsaw? The clutch drum is removed by removing the retaining ring, possibly using a simple slotted screwdriver. To remove the clutch, you will need a 19 mm wrench and a special piston stopper. In the photo you can see a variety of models from manufacturers Shtil, Husqvarna, Partner, Goodluck. Chainsaw clutch How to remove . The drive sprocket also serves as a drum. Up. Den1309 Blog Disassembling the Shtil 180 chainsaw. Remove the caps from the tanks. Remove the ignition coil by unscrewing a couple of bolts. Full size. Removing the ignition coil. Saws. Do-it-yourself repair of the Shtil 180 chainsaw: video instructions. To watch it, remove the cover from the carburetor and twist the special screen located behind the chainsaw drum. chainsaw , namely the MS 180 model, is used primarily for harvesting wood and performing various construction work. Such equipment is used very often due to the large list of functions and capabilities. chainsaw is not the cheapest to repair and has some factory defects, but at the same time it is light, compact and high-speed. Convenient to use. We remove the breaker by unscrewing the two 19 nuts with a spark plug wrench. How to remove the flywheel from a Chinese chainsaw? Be careful, there are many fakes for the STIHL Shtil MS 180 chainsaw model, watch the video so as not to become a victim of scammers. Many saw owners do not think about how to remove the clutch on a chainsaw themselves, because they have the opportunity to contact a service center. We unscrew the clutch clockwise. Fuel filter is dirty. You should remove the fuel hose and check how the fuel flows. If the stream is weak, you may need to clean the filter. Hello, I have a question. chainsaw , when it starts at idle speed, works better than new, but Where it is used: all STIHL chainsaws. 16. Clutch .

READ How to choose a STIHL chainsaw

How to unscrew the Shtil MS-180 clutch

Ms-180.

How to remove grip on benzo Pila

how to unscrew the clutch

on
the chainsaw
for repair. how to loosen the grip on the chainsaw for repair.

remove it to replace the sprocket by removing only one retaining ring. Replacing the chain sprocket is very simple: it can be changed. How to unscrew the clutch on a chainsaw. Uploaded April 7, 2021.Chinese Calm 660 won't start Repair. Uploaded on August 27, 2021. How to remove the sprocket, clutch and flywheel on a STIHL 361 chainsaw. Disassembling the STIHL MS 180 chainsaw. Removing the flywheel, ignition module and clutch . repair chainsaws repairshtil180 repairstihl. How to remove the cylinder and piston of the STIHL 180. Disassembling the STIHL MS 180 chainsaw. Removing the flywheel, ignition module and clutch . repairschainsaws repairstihl180 repairstihl. The Stihl 180 chainsaw is operated in accordance with the instructions supplied with the tool. When the surface is completely free of debris, the repairman removes the cover, and then the filter. The Shtil 180 chainsaw has a characteristic malfunction, which consists in insufficient sealing of the installation site of the oil hose in the chainsaw body and the appearance of a leak at this point. To eliminate it, just remove the handle of the Stihl MS 180 saw. How to remove the clutch from a chainsaw: a detailed report. The clutch repair process consists of the following operations: Contents 1 Features and technical characteristics of the Shtil chainsaw 2502 Shtil chainsaw STIHL declines all liability for personal injury and material damage resulting from hard, difficult-to-remove deposits, especially in the saw chain drive area, clutch and on the saw chain until the oil pump is completely blocked. Question: How to remove the clutch from a Shtil 180 chainsaw? Answer: The clutch drum is removed by removing the retaining ring, possibly using a simple slotted screwdriver. To remove the clutch, you will need a 19 mm wrench and a special piston stopper. In chainsaws from Stihl or Husqvarna, the replaceable crown is located directly on the shaft. How remove the drive sprocket from a chainsaw? Removing the saw bar along with the chain Disconnecting the clutch from the engine (the piston must first be locked) How to remove and replace the sprocket from the chainsaw? After removing the clutch, the approach to internal parts of the device, that is, after removing the coupling, you can remove the sprocket. Remove the air filter cover and clutch cover. Chainsaw operation. It is impossible to stop the engine with the chain brake on chainsaws, as this can lead to overheating of this unitSTIHL MS-180 has a clutch consisting of three sections. Dismantling chainsaw Stihl 180 part 1. Stihl crankcase assembly professional saw. Instructions and tools - no, I haven’t heard of them. Assembly of MS STIHL 361. How to remove the flywheel from a Chinese chainsaw? Common malfunctions of the Stihl chainsaw. How to eliminate a broken chain is clear to everyone; buy a new one. A sign of a clogged carburetor is also carbon deposits on the spark plug. The carburetor should be removed from the unit and disassembled for subsequent cleaning.

READ DIY Cordless Saw

Application online

MS 260, MS 361 16″, MS 361 18″, MS 180, MS 211 14″, MS 180 C-BE, MS 181, MS 181 C-BE, MS 230, MS 210 C-BE, MS 211 C-BE 14″, MS 210, MS 192 T, MS 192 CE, MS 250, MS 230 C, MS 270, MS 230 CB-E, MS 260 15″, MS 290, MS 280-I, MS 200 T, MS 250 C -BE Ergostart, MS 341, MS 260 N (16″), MS 361-W, MS 390, MS 440-N (20″), MS 261, MS 440-W, MS 361 16″, MS 361 18, MS 460, MS 440, MS 362, MS 441 18″, MS 650, MS 441-W, MS 660 N, MS 660, MS 460-R, MS 880

• Blog
• About the service center
• Brands served
• Prices for diagnostics and repairs
• Delivery
• Spare parts
• Contacts

Repair and service of garden equipment in Moscow.

Specialized service - comprehensive warranty and post-warranty service for gardening and municipal equipment from world manufacturers! We sell spare parts with delivery throughout Russia!

Clutch faults

Reasons why clutches need to be disassembled:

• Faulty or burst spring;
• As a result of loads on the chainsaw and wear of parts, the spring left its place;
• Chips on the clutch plate;
• Wear of parts.

We choose the Shtil clutch 180, 250, 361 and other models

Once again, the Stihl clutch has a very simple design . This makes it easy to disassemble the mechanism and try to fix the problem yourself. Fortunately, our catalog contains all the necessary parts at the best prices.

But we still recommend replacing the clutch mechanism as a whole. Constantly changing parts that will fail one after another is a troublesome and unpleasant task. After all, just because of one broken spring or cracked cam, you won’t be able to use your gas saw.

And in our catalog you will find clutch mechanisms of both original and third-party production for all popular models of Shtil chainsaws:

• The third-party clutch for Shtil 180 is presented in our store from the Oregon company (Canada). Its quality, reliability and durability are comparable to the original part from the German manufacturer;
• For the 250 model, high-quality spare parts are manufactured by the Serbian company Saber, which itself produces gasoline saws under its own brand;
• Woodman produces reliable coupling devices for the Stihl 270. The main sales market for this spare parts manufacturer is the United States of America and Canada, and therefore the quality of its products fully complies with the quality requirements of the North American region;
• The coupling mechanism for the 351 is produced by Winzor (USA). Another manufacturer of high-quality and reliable spare parts;
• We recommend installing coupling devices manufactured by Rapid (Austria) on the Shtil 361 chainsaw. This company generally produces a wide range of spare parts for German semi-professional and professional class chainsaws;
• For the Stihl 660 chainsaw, we recommend installing, depending on the place of its assembly, either spare parts produced by Taiwanese companies, if the chain saw is assembled in China, or a coupling device manufactured by companies from Europe and the USA, if the gas-powered tool was assembled at the German Stihl plant.

In our online store you can buy chainsaw clutches and other popular brands at a competitive price.

Our many years of work are aimed at troubleshooting garden tools of varying degrees of complexity. But this is only half the success. We try to work responsibly, taking into account the wishes and needs of the client. This allows us to maintain our brand in the services market.

You can contact us either by phone or by leaving a request on the company’s website. Our specialists will come, assess the scale of the work, pick up the broken tool and bring back a working one. From 10,000 rubles for repairs, delivery is free. We work quickly, guarantee quality and offer affordable prices.

From then on, you won’t have to worry about repairing your chainsaw, just contact us, and your garden equipment will always work properly.

Repair and replacement of chainsaw clutch

In order to eliminate any of these faults, it is necessary to remove the clutch. To do this you will need to perform the following steps.

• Unscrew the nuts and remove the chain sprocket cover.
• Remove the guide bar and chain from the chainsaw.
• Release the saw chain brake and remove the chain sprocket. To determine the condition of the clutch mechanism on Stihl chainsaws, it is necessary to remove the sprocket with the clutch drum. On Husqvarna chainsaws, this is simply done by removing the chain sprocket cover. Before removing the clutch, block the engine crankshaft.

You should also keep in mind that you will need special tools to remove the clutch on most chainsaw models. We also recommend that you monitor the cleanliness of the clutch mechanism and, if necessary, clean it before further use.

In most cases, when replacing the clutch, it makes sense to update the guide bar and chainsaw chain.

If you suspect a malfunction of the tool, and do not have sufficient skills and time to repair it yourself, contact our Direct Hands service center, service specialists will perform qualified diagnostics and repair of chainsaws of leading brands for you.

In the video, repairing a Stihl chainsaw clutch, replacing a drum with a drive sprocket

Types of clutch malfunctions and ways to eliminate them

Here the list of possible breakdowns is not so long, the most common cases are:
Damaged spring , it can be stretched or burst, in both cases the clutch will not work and repairs are necessary. Depending on the brand of chainsaw, you will have to replace the spring or the entire clutch. So, for example, on Stihl saws it is possible to replace the spring, but on Husqvarna and Echo you will have to completely change the clutch.

Clutch drum , on which the chainsaw drive sprocket is located. Wear of the drum and sprocket also impairs the performance of the clutch mechanism; it is determined quite simply; wear inside the drum and on the sprocket is visible to the naked eye. The problem can be eliminated by installing a new clutch drum.

Another type of failure is a faulty bearing inside the clutch drum; its wear is also natural, although not as frequent as compared to the cases described above. On many models of chainsaws, this bearing is replaced, and there is no need to change the entire clutch.

Principle of operation

Before identifying a malfunction and repairing the Shtil 180 chainsaw, you should study the principle of its operation and what structural elements it consists of. A chainsaw must contain its main element - a two-stroke engine. It is he who is responsible for the reliability and performance of the device. The engine is involved in starting the chain drive and maintaining its movement under the influence of the centrifugal clutch. In addition to the electric motor, the chainsaw includes:

• starter;
• flywheel, also known as a cooling unit;
• ignition unit;
• clutch and brake mechanism;
• carburetor with STIHL compensator;
• air filter;
• fuel and oil tank;
• muffler;
• anti-vibration system.

Fuel from the tank enters the carburetor , where it is mixed with air coming from the cleaning unit. From the carburetor, a mixture of air and fuel enters the engine. The saw carburetor has one adjustment screw that controls the idle speed. All device settings are made at the factory and ensure optimal supply of the fuel-air mixture.

The mixture is ignited in the engine cylinder, and the engine is started using the starter. Under the action of the piston, the shaft that is part of the crank mechanism begins to move. There is a sprocket on the shaft onto which the chain links are placed.

The chainsaw uses a single-cylinder motor.
A clutch is used as a protection mechanism, which allows the electric motor to switch to idle mode in the event of a chain jam. At the initial revolutions, special linings located in the radial direction are pressed by springs to the middle of the shaft, thereby preventing it from rotating. At high speeds, centrifugal force increases, which leads to compression of the springs. The linings are pressed away from the center of the shaft, the sprocket rotates and the chain starts. The electrical circuit of the device is involved in the ignition system. Due to the use of a flywheel with magnets, an electromotive force (EMF) is generated during rotation, which leads to the appearance of current in the electronics unit. The block sends a signal to the spark plug, causing a spark to appear at its terminals. This spark ignites the mixture coming from the carburetor. After a successful start has occurred, the chainsaw begins to repeat all work processes in the cycle.

The device chain is made up of teeth and connecting elements. To protect the user from kickback, the device is equipped with a brake system. Oil supply occurs automatically under the action of a pump.

Prices for Stihl chainsaw repairs

Didn't find what you were looking for?

Leave your phone number and find out the cost of repairs within 15 minutes!

By filling out the form and clicking on the “Submit” button, you consent to the processing of your personal data.

• About Us
• Delivery
• How it works?
• Helpful information
• Contacts
• Site Map

Copyright REMMARKET © 2012 — 2020

All rights reserved. The use of site materials is prohibited.

Submit a repair request

Enter your feedback information and our manager will clarify the cost, as well as the nearest possible date for repairing your instrument.

Please call back

Enter your feedback information and our manager will clarify the cost, as well as the nearest possible date for repairing your instrument.

Thank you!

Your application has been successfully sent. In the next 15 minutes, a manager will contact you and clarify the details of the order.