You have only recently owned a chainsaw, and you still don’t know which oil is best to use to lubricate the chainsaw chain. The lack of this knowledge can have a detrimental effect on the tool, since the type and quality of the lubricant determines how long the tire and chain of the tool will maintain their functionality.
After reading this article, you will fill the gap in knowledge, because... We will consider the issue of using oils from various manufacturers and brands to reduce friction between the parts of the saw set. We’ll also figure out what additional lubricants are used to service the chainsaw in order to maximize its service life.
What oil to use to lubricate a chainsaw chain
To answer this question is quite simple; to do this, you need to open the instructions for any saw and it will indicate that you need to fill in oil that has a good adhesive effect.
Adhesion is a measure of the adhesion of a material, in this case oil, to the metal surface of the bar and chain.
Why is this necessary? The fact is that the chain moves along the bar at high speed, and if oil, which has low adhesion, is used as a lubricant, then most of it, by inertia, flies off the end of the bar and lubrication of its lower part does not occur. This phenomenon can be observed if you conduct a small experiment. Start the chainsaw, point the end of the bar towards a light-colored surface and add gas as much as possible. As a result, oil stains will appear on it, which is proof of the theory.
Saw chain lubrication oils
- Stihl for chain lubrication (volume 1 l). This is a synthetic-based lubricant that completely prevents chain clogging during long-term use. Price 215 rub.
- ForestPlus is a mineral oil, packaged in different types of containers. It creates a film on the bar and chain that holds even at high speeds. The price category starts from 293 rubles.
- BioPlus is a plant-based lubricant that is environmentally friendly. It is packaged in several types of containers, the price depends on its type, and is different in each region, starting from 444 rubles.
- SynthPlus is a semi-synthetic oil, works even at minus 25 degrees, mixes well with BioPlus, which makes it easy to switch from one type of oil to another. Packaged in similar containers as the previous one. Price from 369 rub.
the saw chain with BioPlus oil, since other oils are intended for harsh conditions or work in the winter season.
All modern chainsaws have a separate oil circuit for lubricating the cutting elements of the chain.
The quality of saws depends largely on their condition and working conditions. Therefore, companies that produce accessories for chainsaws create special brands of oils that ensure reliable lubrication of the surface.
Chainsaw sprocket lubricant
To increase service life and reduce friction on the drive sprocket, the manufacturer equips this mechanism with a needle bearing, which must be periodically lubricated. Stihl Multi-Purpose Grease can be used for lubrication.
If you do not want to overpay, it is better to use an inexpensive, but no less high-quality option, Litol or Litol 24 lubricant. Due to its viscosity, Litol will easily replace the original one.
You can lubricate the chainsaw tire sprocket with the same lubricants as the drive one, using a special syringe for this. This allows grease to be pressed through the technological holes in the tire to the sprocket bearing.
Manufacturers of adhesive oils
Almost all manufacturers of chainsaws are engaged in the production of consumables for them, explaining that these products are most suitable for use in conjunction with their saws. There is no information to what extent this is true, but based on the experience of operating and repairing chainsaws, it can be noted that there are no significant differences in the service life of parts or at least visible wear.
But a fact is a fact, the manufacturers recommend it and it cannot be hidden. So, let's go back to the manufacturers, and let's start with the popular brand Shtil.
Stihl Adhesive Oils
The company’s website presents the following adhesive oils, designed for various operating temperatures and having good lubricating properties:
- ForestPlus adhesive oil - recommended for use at temperatures down to - 15 °C, shelf life under storage conditions is 3 years. Supplied in liter or five liter containers;
- BioPlus - its feature is a plant base, which allows it to quickly decompose when released into the soil. Suitable for use down to minus 15, supplied in three, five and one-liter containers;
- The latest SynthPlus oil is distinguished by its ability to maintain performance at temperatures as low as minus 25 °C.
HUSQVARNA oils
The company offers its customers Husqvarna Bio Advanced oil for use in normal and extreme conditions. The oil is made from plant components and is safe for the environment, supplied in liter and five-liter containers.
As an economical solution, the company has Vegoil oil; according to the manufacturer, its consumption is reduced by 40% compared to others. Supplied in liter containers.
List of the best
Now let’s actually get acquainted with the most optimal oils, both in terms of quality and price category, that are widely used for chainsaws from the manufacturer Shtil. And let’s directly give them a short description, so:
- 4-stroke oil Viking HD 10 W – 30
This kind of oil is widely used directly for small four-stroke engines. It can be used regardless of the time of year, but you must remember that the air temperature should not be lower than -15 °C. This oil is sold directly in bottles with a capacity of 0.6 liters and costs around 360 rubles.
- Oil for two-stroke engines 100 ml
This oil can be bought in a bottle with a capacity of one hundred milliliters for only 90 rubles. It must be added directly to gasoline. The ratio of their quantity should not exceed 1:50, that is, 20 grams. oil and one liter of gasoline.
Moreover, this kind of lubricant was developed specifically for the equipment of the manufacturer Shtil. Its main component is minerals. But it can also be used in other models from other manufacturers. The main thing is that these chainsaws have a two-stroke engine.
- Stihl oil for two-stroke engines 1l
The weight of the container in which the oil is sold is equal to one liter. It is intended directly for Stihl chainsaws, but can also be used perfectly for tools from other manufacturers. Diluted directly with gasoline 1:50. And the basis of this oil is minerals. This kind of assistant will cost you around 500 rubles.
- Stihl oil for two-stroke engines 1l. with dispenser
Sold in a bottle with a capacity of one liter and which has a direct dispenser for three and five liters.
Diluted with gasoline in a direct ratio of 1:50. The oil was made specifically for two-stroke chainsaw engines from the manufacturer Shtil. It is also made on the basis of mineral additives. Also widely used for instrument models from other manufacturers. The main thing is that these chainsaws have two-stroke engines. Costs 600 rubles.
Is it possible to fill in Stihl HP Ultra oil for two-stroke engines 100ml
This kind of oil can be purchased in a bottle with a capacity of one hundred milliliters. It must be added directly to gasoline in a ratio of 1:50. Manufactured directly for chainsaws by the manufacturer Stihl.
It is a fully synthetic oil, which directly has a high level of lubricating benefits. It can also be used directly for other models of chainsaws that have two-stroke engines. This kind of oil costs around 120 rubles.
Engine oil for Stihl saws (Stihl) for two-stroke engines 5l
Sold directly in a canister with a volume of five liters. Intended for dilution with gasoline in a ratio of 1:50. Contains mineral additives and was created specifically for two-stroke engines of Stihl chainsaws. It is also widely used for lubricating engines of chainsaws from other manufacturers. The price category is 1500 rubles.
Stihl HP Ultra chainsaw oil for two-stroke engines 1l. with dispenser
The oil is sold directly in a bottle, which has a kind of dispenser for three and five liters. Intended for dilution with gasoline, the ratio of these additives should not exceed 1:50.
This oil was made specifically for tools from the manufacturer Stihl. Widely used and applied to devices of other brands that have two-stroke engines.
This oil costs 1100 rubles.
How to use Stihl chain oil 1L
Sold in a bottle with a capacity of one liter. It is a synthetic-based oil that has a high level of lubricating properties. Moreover, with the help of this type of oil you can completely prevent direct grinding of the chain during its long-term operation (see how to sharpen a chain). The price category is 215 rubles.
How to replace the original expensive oil and is it worth it?
In situations where it is not possible to use original ones, they can be replaced with oil for car engines. Cheap automobile oils such as Autol or diesel lubricants, due to their reduced adhesive properties, are unsuitable for long-term use.
Some owners, despite the recommendations, still use analogues, preferring to change the tire and chain more often, but here everyone decides for themselves. Such oil cannot have any negative effects on the lubrication system, which means the difference is only in the quality of protection of the tire from chain friction.
A little about lubrication of a chainsaw chain by working off
Used oil is oil that has served its useful life in a vehicle's engine or gearbox. Many chainsaw owners, trying to save money, use it to lubricate the chain, which results in serious repair costs.
The reason for these breakdowns is the presence of impurities in the waste metal, metal shavings, which settle in the crankcase of the car, and when the waste is drained from the sump, it merges with it.
When metal shavings fall on the tire, they act on its surface as an abrasive. Simply put, instead of protecting the surface, grinding increases wear on the tire, drive sprocket, and driven sprocket bearing on the tire. Working off also affects the chainsaw chain in those places where it bends and increases the risk of breaking the chain mechanism.
Conclusion: to lubricate the chainsaw chain you need to use original lubricants from the manufacturers. It is unacceptable to use waste from a car engine. In the absence of high-quality oils, short-term replacement with clean automobile oils is allowed.
At a gas station I decided to buy oil for the chains of my Stihl MS180 saw. Oil I-40, it is written that it is for lubrication of sliding guides. The consistency is very liquid. By price
1$ per liter. Is it suitable for winter time?
Lubrication system malfunctions and how to fix them
The main malfunctions of the oil supply system on a chainsaw can be divided into two main types: these are general malfunctions inherent in all chainsaws and individual ones, which may vary depending on the type of pump and worm gear installed on a particular model. Let's begin to understand the faults in order.
Operating a chainsaw without lubricating the chainsaw chain is prohibited. This has a detrimental effect on the bar, drive sprocket and chain, and can result in significant repair costs.
Signs of a malfunction of the lubrication system, checking its performance
- The chainsaw chain is dry and has a pale tint without shine.
- The chain stretches relatively quickly.
- The tire is very hot and may even partially melt the paint.
- The oil from the tank is practically not reduced.
- Reduced cutting efficiency on a sharp chain
All these signs indicate that the lubrication process is not proceeding properly. In order to check the oil supply to the lubrication system, you need to remove the side tire of the chainsaw and start it. Next, you need to slightly increase the speed while observing the end of the oil line. If oil comes in, most likely the amount is not enough for normal lubrication and you need to clean or replace the filter and, if possible, adjust the flow. If it does not, the problem is more serious and requires further diagnosis.
Read also: Compressive strength MPa what is it
There is a way to check the oil supply without removing the tires. To do this, you need to point the end of the bar towards, for example, a freshly cut piece of wood from the side of the cut and increase the speed as much as possible, while trying to keep the end of the bar at a distance of no more than 10 cm from the block. If oil spots begin to appear on its surface, it means the oil is being supplied.
Troubleshooting
Once it has been determined that oil is not being supplied, further diagnosis is only possible if the oil system is completely removed. Of course, in some situations replacing the filter helps, but this is very rare.
Access to the oil pump of some models of saws is possible only after complete disassembly; therefore, without having the skills to repair gas-powered tools, it is better to entrust repairs to professionals.
Most common faults
- Broken oil hose. It can sometimes be detected by visual inspection. The problem is solved by replacing the faulty part.
- There is no thread on the oil pump shaft; replacing it will help.
- A defective thread on the pump drive gear can be similarly solved by installing a new part.
- Lack of main shaft corkscrew (relevant for some instrument models, for example, Homelite). You can fix it by installing a nail of a suitable diameter instead of the original corkscrew, cutting it to the required length.
- Blockage in the line. Can be removed by blowing with compressed air or mechanically, using a wire of a suitable diameter.
- Filter element clogged.
- The Stihl MS 180 tool, whose pump is not dismountable, often gets clogged. You can try to wash it in clean gasoline, if that doesn’t help, replace it.
- In Chinese chainsaws (Gypsy), it very often cuts off the grooves on the main gear, through which the force from the sprocket is transmitted to it.
Individual malfunction of the Stihl MS 180 lubrication system
Due to the fact that the Stihl MS 180 is one of the most common models of chainsaws, I would like to dwell in more detail on one fault inherent only to it and describe a method for eliminating it without replacing parts.
Quite often, on the Shtil MS 180 chainsaw, depressurization of the oil line is observed in the place where the oil line coming from the tank is installed in the saw body. The malfunction can be determined by the characteristic lubricant leaks on the bottom of the tool.
To eliminate the problem, you need to remove the chainsaw handle, remove the hose from the mounting hole, clean and degrease. After all these manipulations, apply sealant to the hose seat and install it into the chainsaw body.
You can learn more about troubleshooting and complete diagnostics of the lubrication system of the Stihl chainsaw by watching a video that shows the step-by-step process of disassembling and repairing the lubrication system.
Tags: choosing oil for lubricating a stihl chainsaw chain in winter
Comments 43
If you cut all day long, you can pour I-40 and other new ones. Well, what the heck - it stinks, then everything turns black, the oil pump can skip if it’s not filtered. Yes, and all the sawdust is in this mining, all of this is then absorbed into the ground.
If you cut several cubes for yourself, then buying 1-2 liters at 2-3 € per liter of good, proper oil is not such a big waste.
Specialist. Chain oil is mostly mineral, there are even biodegradable oils. It is sticky and stretches like snot. I recommend not saving. It also depends on the saw; on normal saws the pump turns only when the chain moves, and not constantly. You can also reduce the feed. The right oil is used correctly. On the Huska 550XP, one oil fill was enough for me for 1.5-2 gas fills. And at two gas stations you can cut quite a lot.
PS And the tire is killed by improper use, a dull or incorrectly sharpened chain. And only new chains stretch, and then only a little, if the sprocket is not dead.
We use m8v, popularly “eight” or “autol”. The work is seasonal, from early spring to late autumn. Tires and chains wear no more than with the recommended oil.
I fully support it, I used it before, compared the price when purchasing, at this I-40a gas station the price (13.15 Belarusian rubles) was the cheapest, although in online stores the price of M8B and I-40a is almost the same
Once I suggested to a friend to use a gl-5 transmission to lubricate the chain. I spent the summer building a house.
As a result, the tests were successful. He said that the chain began to stretch much less, and he liked the saw’s performance.
The only downside, as he said, is that it stinks more during work)
Now only his is pouring.
I have a Shtil 180 and it’s about 20 years old, and even the original piston one, and it works in the spring and fall, God willing, and I use the exhaust all the time, but I try to take the exhaust from gasoline, it’s much cleaner.
Any clean (new, NOT used) industrial or motor oil will do, I rely on my 10 years of experience working with STIHL saws. The viscosity should be poured depending on the season. For example, in winter you can fill in a very viscous one, only so that the oil is warm. There is no need to pour oil, the oil pump doesn’t like it.
I agree, that’s what I bought, it’s clean, new, it doesn’t feel very viscous, when looking at the counter, all the motor and transmission ones were more expensive. I didn’t take the heat into account; in winter I’ll store it in a warm pantry and not in the garage. Thank you.
User manual
The passport of the petrol saw “Shtil” MS-180 is the instruction manual, which contains complete information about the tool itself. Before starting operation, you must carefully study the manual to avoid annoying malfunctions.
We suggest you read the instructions for the chainsaw.
Device
Chainsaw “Shtil” MS-180 consists of: gasoline engine, carburetor, casing, starter, flywheel, clutch, decompression valve, oil, fuel pump and tank, spark plug, saw chain, tire, sprocket, brake, air filter, shift lever , dust collector, muffler, clamps, tension wheel, gear stop, adjustment screw, handle.
Preparing a Stihl chainsaw for work
The preparation of the saw should be approached with all responsibility, since its service life in the future, as well as the safety of the operator, depends on this. Let's consider the correct algorithm of actions when preparing a chainsaw for operation:
- The Stihl chainsaw is assembled (according to the descriptions and diagrams in the manual);
- the splint is put on and secured;
- the chain is tensioned;
- the fuel mixture is prepared correctly: gasoline is diluted with oil in a ratio of 50/1 (the amount of AI-92 gasoline is 5 liters, special Stihl oil for two-stroke engines is 100 ml);
- the fuel mixture is poured into the tank;
- Chain lubrication oil is poured into the tank;
- the reliability of fastener tension is checked;
- the saw is started according to the instructions;
- the carburetor is adjusted at idle speed with the appropriate screw (the chain should not move);
- The supply of lubrication to the chain is checked.
We invite you to watch a video about how to assemble the Shtil chainsaw:
Our video will tell you how to start the Shtil 180 chainsaw:
Chainsaw chain oil
Break-in period for the Shtil chainsaw
In the usual sense, there is no break-in for the Stihl 180 saw. It is initially ready to work. However, the equipment owner needs to know and understand the following:
For the first 4 to 8 full fuel tanks, the operation of the gasoline saw should be carried out in a gentle mode, not at the full power of the power plant, with frequent breaks to cool the tool. The first 60 minutes of operation of the Calm chainsaw consists of intervals of work and rest: 2 min. work, 10 seconds - idle, break
Idling for more than 10 seconds damages the spark plugs, leaving carbon deposits on them. It is very important to properly prepare the fuel mixture from high-quality materials (1/50, AI-92 gasoline and higher, Stihl oil for 2-stroke engines).
Maintenance
Before use, check:
- chain condition, sharpening;
- chain tension;
- tightening fasteners;
- filling fuel and oil tanks;
- presence of chain lubrication;
- idle speed, etc.
After sawing work the following is carried out:
- cleaning the chainsaw;
- the chain tension is weakened (required);
- chain sharpening (if necessary);
- condition of the tire, its wear;
- filter maintenance (as needed).
New owners are often lost and looking for materials on how to properly disassemble (assemble) the Shtil 180 chainsaw. We suggest watching a video that shows how to disassemble and reassemble the Shtil 180 chainsaw:
Malfunctions and repairs
Malfunctions of the Stihl 180 chainsaw and their elimination are another problem that worries tool owners.
Why does the Shtil 180 chainsaw not start:
- no fuel mixture;
- no contact on the spark plug;
- break of a high-voltage wire;
- the fuel pump does not pump;
- fuel lines are clogged;
- problems with candles;
- ignition is not adjusted;
- pours a candle.
Why does the Shtil 180 chainsaw not develop the required number of revolutions:
- carbon deposits on the spark plug;
- the spark plug is worn out and needs to be replaced (after 100 hours of operation);
- The carburetor requires cleaning.
Chainsaw “Shtil” 180 stalls at idle:
- carburetor not adjusted;
- The fuel or air filter is clogged.
We invite you to watch a video on how to adjust the carburetor of the Shtil MC 180 chainsaw with your own hands:
Some tool owners use a Stihl MC 180 chainsaw together with a grinder attachment, this allows them to build a home sawmill and perform longitudinal cuts.
The video shows the grinder attachment for the Shtil MS-180 chainsaw:
But even without this attachment, some craftsmen have found a way to perform longitudinal cuts with a regular bar and saw chain. We invite you to watch a video about a homemade sawmill using scrap materials:
Related Posts
Chainsaw
. What kind of oil is used to lubricate the chain?
Chainsaws. A popular tool for those who deal with numerous household chores. They can be used for different purposes. collect firewood, trim dry branches. But in order for the device to last as long as possible, it is necessary to take proper care of it by choosing the right different connections. A special role is played by chain saw oil, which is selected depending on the principles of the tool and its characteristics.
Types and composition
The choice of specific oil depends on where and how the chainsaw operates. Mineral compounds are suitable for the summer and warm seasons. In other cases, it is better to use synthetic or semi-synthetic oils. If it is necessary to lubricate the chain, there is no need to use waste oils, which will clog the fuel system and then cause serious damage to the tool.
The chainsaw oil must be thoroughly cleaned to ensure that the lubricant is applied correctly and accurately. If you use poor-quality connections, there will be no contact between the saw elements and the bars, sparks will appear, and then the moving parts of the saw will wear out.
Recommendations for choosing motor oils
Even the most expensive motor oil for lubricating a chainsaw is consumed in minimal quantities, so there are no serious reasons for its strict economy.
Based on this, experts advise excluding from your attention cheap counterfeits, which are often sold under the trademarks of well-known manufacturers.
The result of natural selection was a stable demand for motor oils of the Husqvarna and Shtil brands. There are many positive reviews about the quality of Makita brand motor oils. Practice has proven that the performance properties of branded consumables are an order of magnitude higher than those of cheap Chinese analogues.
On the other hand, it should be noted that the quality of Chinese motor oils manufactured at state-owned enterprises is as close as possible to the characteristics of European consumables at an average price level.
Criminals do not miss the opportunity to make money by selling counterfeit products from a well-known brand. Stihl oil is no exception. Most often you can find fake Shtil HP, because its sales volumes are the highest of the entire line of Shtil lubricants.
In order to distinguish a fake from the original, the Shtil company released a special brochure, which recorded all the main differences between the original and the fake.
We also invite you to watch a video that shows, using a specific example, what a package of high-quality Shtil oil should look like and how to distinguish a fake.
- How to Start a Stihl 180 Chainsaw
- How to Cut a Countertop at Home
- How to Clean the Carburetor of a Stihl 180 Chainsaw
- Which Circular Saw is Best for the Home
- Adjusting the Carburetor of a Stihl 250 Chainsaw with Your Own Hands
Oil for chainsaw chains. What oil should I use to lubricate a chainsaw chain?
Chainsaws are a popular tool for those who have to do countless household chores without the help of others. They can be used for various purposes - preparing firewood, cutting dry branches... But in order for the device to last as long as possible, it is necessary to properly care for it, choosing different compositions well. What kind of oil to pour into an electric saw. What oil to pour into what oil to pour into the chain. A special role is played by oil for chainsaw chains, which is selected depending on the operating mechanisms of the tool and its features.
What to consider?
Careful attention should be paid to lubricating the saw chain. First, you should choose a special oil that will not harm the oil pump. In addition, this will ensure proper operation of the self-lubrication system. The chain also requires proper storage, in other words, immersion in oil, and if it wears out, you shouldn’t try to revive an old chain - it’s easier to change it. Which oil to choose for chainsaw chains so that it is non-hazardous and meets all requirements?
Types and composition
You should choose a specific oil depending on where and how the chainsaw is used. Mineral compositions are suitable for summer and warm seasons. What kind of oil to pour into the oil after jumping off the chainsaw chain deteriorates. In other cases, it is better to use synthetic or semi-synthetic oils. If you need to lubricate the chain, you should not use waste oils, which will lead to clogging of the fuel system, and then to severe damage to the tool.
Chainsaw chain oil must be carefully cleaned so that lubrication is carried out well and accurately. If you decide to buy a Stil or Husqvarna chainsaw, read our article. In it we compare the most popular models. If you use poor compounds, there will be no contact between the elements of the saw and the bar, sparks will appear, and then the moving parts of the saw will wear out.
How to choose?
Any chainsaw has a carburetor two-stroke engine and two tanks: one is filled with gasoline, the other is filled with oil. When choosing a lubricant composition, zoning plays an important role - it should be small. Another important indicator is resistance to low temperatures: the oil should not solidify at extreme temperatures, which will ensure the quality of operation of the entire tool.
For lubrication, it is advisable to use adhesive oil for chainsaw chains, which contains special substances due to which the composition adheres well to the chain. High-quality oil will remain on the chain as it rotates, and the chain itself will be more reliable in operation.
Another important indicator of a lubricant is thickness: if the composition is watery, it will be consumed in larger quantities. Husqvarna oil can be what kind and when to pour gasoline into the chainsaw. To avoid harming the environment when using a chainsaw, it is important to use plant-based oil - its waste will disintegrate in the natural environment.
Which chainsaw oil should I choose, since modern manufacturers offer a wide range of options? Among the specialized manufacturers, we can note such brands as Divinol, Bio-Kettenol, Ravenol, VegOil, Mobil, Castrol, Shell. Naturally, you can pour oil into an imported chainsaw, how much oil to pour into. Let's take a closer look at the features of their products.
Divinol
This brand offers chain lubricant of the highest quality, which has good adhesive and lubrication capabilities, so the lubrication is excellent, and the chain links and hinges are firmly protected from wear. The average combination of viscosity and temperature characteristics guarantees that this oil can be used in any season and at any temperature.
Divinol offers a variety of chainsaw oils. Which one should I use? Zweitaktoel FF attracts attention due to its economical consumption, combination with any fuel, prevention of aging of the fuel mixture and good corrosion protection. In addition, this oil can be used at any temperature. Divinol Kettenol and Divinol Kettenol Bio can be used to lubricate chainsaw chains and bars. Using these compounds, you can firmly protect chain links and joints from wear while guaranteeing economical oil consumption. High-quality organic oils of this brand provide excellent lubrication and adhesive properties, so their implementation is not only simple, but also environmentally friendly.
How to choose?
Each chainsaw has a two-stroke carburetor engine and two tanks: one filled with gasoline, the second. oil. When choosing a lubricant composition, zoning plays an important role. it should be minimal. Another important indicator is resistance to low temperatures: the oil should not freeze at extreme temperatures, which will ensure the quality of the entire tool.
For lubrication, it is recommended to use adhesive chain oil containing special substances that allow the composition to adhere well to the chain. High-quality oil will remain on the chain as it rotates, and the chain itself will be more reliable in operation.
Read also
Another important indicator of a lubricant is density: if the composition is liquid, it will be consumed in large quantities. To avoid harm to the environment, it is important to use vegetable oil when using a chainsaw. its waste will decompose in the natural environment.
Which chainsaw oil should you choose because modern manufacturers offer a wide range of options? Among the specialized manufacturers, we can mention such brands as Divinol, Bio-Kettenol, Ravenol, VegOil, Mobil, Castrol, Shell. Let's take a closer look at the features of their products.
Lubricant selection criteria
After purchasing the device, the question may arise about choosing oil to fill the Stihl chainsaw. After all, proper care of equipment increases its performance and saves you from all kinds of breakdowns. The performance of the saw directly depends on the use of good fuel and lubricant.
Read also: Laser for wood cutting
Stihl chainsaws have a carburetor two-stroke engine and 2 tanks (gasoline and oil). To choose the right oil for a Stihl saw, you need to know its criteria:
- It is necessary to determine the manufacturer , because in domestic models they use simple oils (for motorcycles) in a ratio of 1 to 25, and foreign ones use branded lubricant products in a ratio of 1 to 40 (proportions of oil to gasoline). In fact, the owners themselves determine which one to use. You should be prepared that improper use will result in a decrease in power and productivity. Most people use motor oil; if not, then transmission oil. Experts advise using the latter for this manufacturer.
- You need to know the color. For chainsaws with a two-stroke engine, red, green, and blue colors are suitable.
- Compound.
Ravenol
Which chain lubrication oil should you choose? Many people note Ravenol brand compositions. Thus, Ravenol Saegekettenoel S 85 is a special mineral oil created in Germany from high quality base oil with the addition of various additives. It is suitable for saw chain lubrication and has good adhesive and lubricating properties. Thanks to special additives, the oil remains on the chain even at high saw speeds, and the chain itself becomes more reliable in operation. Provides oil and reliable corrosion protection even when operating under the most favorable conditions. By using this composition you can:
- reduce vibration of the saw chain;
- reliably protect it from corrosion;
- cool the circuit due to good thermal conductivity;
- quickly and cleanly cut all types of trees.
Stihl BioPlus
Read also
Probably every user listens to Stihl brand products. The eco-friendly chainsaw oil is calm, effective and based on plant components. Chain oil is of high quality, which can be appreciated in any climatic conditions. Stihl's eco-friendly products have always been popular among customers. Of particular note is the Stihl BioPlus chain lubricant, which is designed to work with high-speed chains. This is different:
- grease resistance;
- excellent adhesion thanks to special additives;
- excellent protection of the cutting set;
- excellent fluidity, which is maintained even at low temperatures;
- oxidation resistance.
The most important thing is that the oil is absolutely safe for the environment, as it decomposes naturally.
Stihl semi-synthetic oil
Stihl chain saw oil is an environmentally friendly lubricant as it is made from high quality virgin raffinates. The oil does not contain impurities that can pollute the environment. This tool can be used in any climatic conditions, and it will be equally effective even at low temperatures. Stihl chain oil provides reliable wear protection for saw chains. You can buy this composition in different volumes. it depends on the characteristics of the chainsaw and the degree of load on it.
Oregon
What kind of oil is used to lubricate chains and how to choose one so that it can be used at any time of the year? The Oregon brand offers connections that are suitable for all types of tools. Viscosity stability guarantees that the oil is suitable for use at any time of the year. The composition includes purified mineral oils to which additives are added. The peculiarity of Oregon compounds is that they are made on the basis of high molecular weight compounds. The distinctive features of the oil are:
- protection of the guide bar and chain from overheating;
- vibration reduction;
- preventing corrosion due to the formation of an oil film.
Thanks to special adhesive additives, this oil acquires greater viscosity and viscosity, so even at high speeds it will not splash and remain on the chain and bar. Regular use of oil can reduce the load on the cutting set and, in general, the entire mechanism of the chainsaw. Special additives can reduce the energy consumption of the saw, which increases the efficiency of the sawing process. The main thing is that when using these tools, deposited deposits are not formed.
Which Oil is Best for Chainsaw Shtil 180
Content
Which oil to choose for a chainsaw? Calmness: practical advice
Undoubtedly, every owner of a chain saw knows that it is important to have good, high-quality oil for direct lubrication. And, probably, there is no need to say that this is a kind of “life force” for this device to produce full and effective work. Today there are a huge number of oils, and, as they say, there is a lot to choose from.
But, unfortunately, not every owner of this type of electrical equipment knows what kind of oil you need to make for your iron friend, so the operation of the chainsaw was not only easy, but also productive. Therefore, in this article we will consider the issue of choosing the right oil for the chainsaw manufacturer with peace of mind. And also, what it should be like to help the chainsaw during its immediate activity, and not harm. So let's get started.
Let's talk about the oil supply device directly to the chain
First of all, I want to emphasize the fact that all the manufacturer’s chainsaws have fairly quiet dimensions, but, nevertheless, they are very powerful. It is these functions that attract potential buyers of such equipment to the models of this company. In addition, you can easily perform various manipulations with this device in relation to wood (see How to cut wood).
Device for supplying oil to the chain. In addition, chainsaws have a high level of cutting power . In addition, this method is equipped with the latest accessories, additional features that promote convenience and ease of use. But actually, let's talk directly about the device that equipped the manufacturer with chainsaws. The chainstay chain lubrication system therefore consists of:
- Tires for tires;
- Chain Saw;
- Oil pump.
It should be noted that the direct oil supply through the pump operation has a special adjustment . Equally important is that the chain is lubricated throughout the operation of the chainsaw. It is for this reason that this piece served its owner for a long time.
There is no doubt that during operation the chain must be systematically lubricated, so oil must continuously flow onto its surface. Since this is all straight tool design.
During use of the device, oil begins to flow directly from the tire groove and is immediately absorbed by the sawdust.
That is why the process of lubrication of the chain area is automatic . But it should be noted that there are models that have a so-called “dosage” of oil, which must be supplied directly to the chain. And, naturally, models whose price category is quite low have only a manual pump directly using a drive, which is located on the handle.
READ Goodluck Chainsaw Carburetor Tuning
Choose the right oil
After you purchased the device, you immediately had a question: what kind of oil can you safely fill with a chainsaw? If you take proper care of the equipment intended for work in the construction and gardening sector, you can significantly increase the level of activity of the direct operation of the device itself, without encountering faults of various natures. Proper Lubrication It should be noted that the most important factors in the immediate performance of the device are the use of the correct lubricant and fuel . Although the main problems for owners of this technology arise with the choice of oil for their “favorites”. In this paragraph, you can learn how to choose a lubricant specifically for the peace of mind of your chainsaw.
First of all, I would like to draw your attention to the fact that almost all chainsaws from this manufacturer have a two-stroke carburetor engine. And also in their “arsenal” there are two direct tanks, namely: gasoline and oil. To choose chainsaw oil, you need to know certain criteria for such a choice.
Firstly, do not forget that, for example, domestically produced chainsaw models require the use of only simple oils that are used directly for motorcycles, and their share should not exceed 1:25. And tools that are manufactured abroad need branded oils, since their requirements are largely exaggerated. And remember that such oils for imported tools must contain a proportion of oil and gasoline equal to 1:40.
Refilling a Stihl MS180 chainsaw, gasoline and oil.
Chainsaw Stihl
MS180 A few points about what liquids should be poured into a chainsaw. Always keep an eye on.
Which chain oil is best to use, choosing chain oil for saws and chainsaws
What kind of oil
select and use for chain lubrication
of chainsaws
/power saws.
In fact, if you look at it this way, only you, as the owner of the technology, can determine what kind of oil you are using. Naturally, you can pour oil into an imported chainsaw from a domestic manufacturer. But then you must be prepared for the fact that the power and performance of your tool will be significantly reduced. Engine Oil Also, it should be noted that there is no definite answer as to what kind of oil is supplied to the chainsaw chain. Basically, the owners of such a device used motor oil, and if they don't have them, then they use transmission oil.
If you believe the experts, then in fact any oil can be applied even to what you pour directly into a Zhiguli brand car, but there are certain features, namely: engine oil can be used for the Hurstavna brand, and the gearbox for peace of mind . exclusively gearbox.
READ Chainsaw Does Not Gain Speed and Stalls Reasons
In addition, to choose the right oil, you need to know what color it should be . Like, for example, for a chainsaw, an engine with two-stroke oil must be red, blue or green. Additionally, when you purchase oil, you should consider which oil is recommended by your equipment manufacturer.
In addition, you can make it much easier for yourself to purchase and purchase a special oil for a quiet chainsaw, the price of which is so high and was produced by “your” manufacturer. And then you can be sure that your chainsaw will not fail. Sure, you can buy cheap oil, but it's worth it, and then complain that your chainsaw is too small for you.
Any chain needs sharpening. Find out more about chain sharpening machines in our article.
Among the necessary movements are with a chainsaw and carburetor adjustment.
Another useful guide for chainsaw owners: How to start a chainsaw.
List of the best
Now let's get acquainted with the most optimal oils, both in terms of quality level and price category, which are widely used for the peace of mind of the chainsaw manufacturer. And we'll give them a little characterization directly, so:
This type of oil is widely used directly for low-power four-stroke engines. It can be used regardless of the time of year, but remember that the air temperature should not be lower than 15 ° C. This oil is sold directly in 0.6 liter bottles and costs around 360 rubles.
- Oil for two-stroke engines 100 ml
This oil can be bought in a bottle with a capacity of one hundred milliliters for only 90 rubles. It must be added directly to gasoline. The ratio of their quantities should not exceed 1:50, that is, 20 gr. oil and one liter of gasoline.
In addition, this type of lube was developed specifically for the calm technique. Its main component is minerals. But it can also be used in other models from other manufacturers. The main thing is that these chainsaws have a two-stroke engine.
- Stihl 2-stroke oil 1L
The weight of the container in which the oil is sold is one liter. It is designed exclusively for chainsaws, but also works great with other brands of tools. Diluted directly with gasoline 1:50. And the basis of this oil is minerals. You cost such an assistant within 500 rubles.
- Stihl oil for two-stroke engines 1L. with dispenser
Sold in a bottle with a capacity of one liter and which has a straight dispenser for three and five liters. It is diluted with gasoline in a direct ratio of 1:50. Manufactured oil specifically for two-stroke gasoline engines. It is also made on the basis of mineral additives.
READ Chainsaw Shtil 280 China Video
Widely used also for instrument models from other manufacturers. The main thing is that these chainsaws have two-stroke engines. It costs 600 rubles.
- Stihl HP Ultra oil for two-stroke engines 100 ml
This type of oil can be purchased in a 100 milliliter bottle. It must be added directly to gasoline in a ratio of 1:50. Produced directly for chainsaw manufacturers.
This is a fully synthetic oil that has a high level of lubricating properties. It can also be used directly for other chainsaw models with two-stroke engines. This kind of oil costs around 120 rubles.
- Stihl 2-Stroke Engine Oil 5L
Sold directly in a canister, the volume of which is five liters. Designed for dilution with gasoline in a ratio of 1:50. It has mineral additives and was created specifically for two-stroke gasoline propeller engines. It is also widely used to lubricate chain motors from other manufacturers. Price category. 1500 rubles.
- Stihl HP Ultra oil for 1L two-stroke engines. with dispenser
The oil is sold directly in the bottle, which has a kind of dispenser for three and five liters. Intended for dilution with gasoline; the ratio of these additives should not exceed 1:50.
This oil was made specifically for calming device instruments. Widely used and used for other brands of devices with two-stroke engines.
Such oil costs 1,100 rubles.
- Stihl chain oil 1L
Sold in a bottle capacity of one liter. This oil is synthetic based and has a high level of lubricating properties. In addition, with this type of oil you can completely prevent the chain from immediately grinding during long-term operation (see How to Sharpen a Chain). Price category. 215 rubles.
Summarizing
As we said earlier, chainsaws are an integral part of our daily lives. This is why it is so important to take care of them and look after them.
In this article, you had the opportunity to familiarize yourself with all the nuances regarding the selection and use of the right oil.
Therefore, if you want your chainsaw to last for a long time, just follow these recommendations and then this tool will give you only positive experiences. Before starting the operation, do not forget to start the chainsaw.
